Free shipping on your first order over $5000 – use code TeamUSA at checkout!

Hobart  |  Warewash  |  SKU: BDELRAX-HTSDOM

Hobart BDELRAX-HTSDOM Warewash Undercounter Dishwashers

$16,557.53
Expected delivery date of , to your door
if ordered within hours and minutes
Not Shipping to ?
More Delivery Options

Documents

Reach out via chat, email, or phone—we're here to help make sure it's the right fit for your kitchen. Contact us for more information.

Description

Hobart CLeN Series All-Electric Blower-Dryer Accessory

Left-to-Right • 208 V / 60 Hz / 3-Phase • 2 HP • 10 kW

Upgrade your CLeN conveyor dishwasher with the power of high-velocity heated air. This stainless-steel blower-dryer mounts directly to the unload end of the machine, rapidly wicking moisture from tableware, sheet pans and trays so you can send every rack straight to service or storage—no hand-toweling, no wait time.

Key Advantages

  • 33 in-long stainless-steel drying chamber built for busy commercial kitchens.
  • Positive forced circulation delivers a curtain of heated air across the full conveyor width.
  • Quiet, industrial 2 HP direct-drive blower (200 – 400 CFM) keeps noise low and productivity high.
  • 10 kW Incoloy® electric heaters with thermostat and independent over-temperature protection.
  • Left-to-Right (L-R) operation aligns perfectly with L-R CLeN dishwashers—no field conversion required.
  • Single-point electrical hook-up simplifies installation; control circuit is factory-wired to the dishwasher.
  • Integrated baffles redirect airflow upward, protecting staff and discharge tables from excess heat.
  • NSF-listed, UL/cUL certified and proudly made in the USA.

At-a-Glance Specifications

Compatible dishwasher series Hobart CLeN conveyor models (CL44eN, CL54eN, CL64eN, CLPS/CLCS 66-86eN, etc.)
Direction of operation Left-to-Right (L-R)
Electrical 208 V / 60 Hz / 3-ph  •  Rated Amps 34.2  •  Min. Circuit 45 A
Heating capacity 10 kW total (3 × 3.3 kW Incoloy® elements)
Blower motor 2 HP, splash-proof, direct-drive
Air volume Approx. 200 – 400 CFM
Chamber length 33 in (838 mm)
Additional height above machine ≈ 17 ⅜ in (441 mm)
Vent connection 4 in × 16 in duct stub with locking damper – 400 CFM exhaust
Drain connection 1 in FPT (dryer tank)
Construction Welded & bolted 300-series stainless steel with wrap-around enclosure
Certifications UL, cUL, NSF

Installation Notes

  • Requires single-point 3-phase electrical connection—verify available power prior to ordering.
  • Mounts directly to dishwasher using factory-drilled holes and supplied stainless hardware.
  • 4 in × 16 in vent must exhaust 400 CFM to atmosphere; canopy hoods cannot be used with this accessory.
  • Blower runs only while dishwasher pumps are operating, conserving energy during idle periods.
Important: This is an accessory module only. A Hobart CLeN conveyor dishwasher, compatible table sections and proper electrical/vent connections are required for operation.

Specifications are based on Hobart document F40252 (02/20) and are subject to change without notice.

Features & Specs

Manufacturer

Hobart

Brand_name

Warewash

Specifications

Blower Dryer, Electric, L - R, 208v/60/3-ph, Higher Than Standard, Domestic